Видео

that's an o-ring on that particular nozzle

Correct. Our QuickTech videos are visually focused, with no distractions, direct-to-the-point and accessible to all language speakers. They are not what everyone may be used to, but many like the simplicity of it

😱

Because this paint is designed to go direct to plastic. So a separate primer is not needed. So you actually get better detail because less paint layers.

The lack of sound does throw some people off. The videos are intentionally visually focused so they are accessible and understandable to all language speakers. Maybe we will add some background music

Not yet. For siphon feed styles, remove the paint bottle and attach a bottle full of cleaning fluid (the kind that is appropriate for the specific type of paint you are using). Flush a generous amount through the airbrush until it runs clear. Clean the front caps (as shown in the gravity feed videos). Check the needle for any dried paint and make sure the area where the bottle attaches is clean

Iwata airbrushes are meant to last so virtually everything is fixable!

Using a cotton swab dipped in some acetone, apply around the stuck area, wait a few minutes and then try to wiggle it loose. Repeat if necessary. If you are still unable to get it loose go to our website to the troubleshooting section at this link. See troubleshooting tips and scroll down for a fillable form that get you to our technical department. Please include a picture. Thanks for messaging. www.iwata-airbrush.com/blog/troubleshooting/

Nozzles are delicate little pieces made of various metal alloys. The softer metals create optimal metal to metal seals and are delicate by nature. Meaning, they are subject to wear and tear under normal usage conditions. This is increasingly so when frequent and/ or aggressive cleaning practices are employed. So, it happens. We recommend not over tightening (a common mistake) when placing a new nozzle. Depending on frequency of use and cleaning practices, it is normal to replace a nozzle. Some people experience broken nozzles frequently, others go for years without a replacement. It really depends on all all the variables. We recommend having a spare on hand.

😅

For a successful conversion you will need to convert the needle, nozzle and nozzle cap

@@iwatamedea1 Domo Arigato!

We don't think artists must choose one or the other. Templates have their purposes, like masking and projecting. They can be useful tools to establish proportions of a piece. Other stencils may be used to establish texture and are commonly seen as time savers in certain settings or for specific types of work. Stencils don't paint it for you. In our view, every piece will also require plenty of freehand spraying.

This sounds like a paint / cleaner issue. Couple of things to think about...Some paints are more difficult to clean out of airbrushes than others. What type / formula of paint are you using? Secondly, the cleaning fluid that you use must be suitable at breaking down the specific paint that you are using. If you are using multiple formulas, these may not be compatible or you may need more that one cleaning solvent. (Ask the paint manufacturer). If you are using craft paint instead of airbrush paint, those will be very difficult to clean (the particles are too large) and will cause a lot of clogs. If you are using thinners, are you using the manufacturer recommended thinning agent? Give these variables some thought as this is likely a paint issue, not an airbrush issue

@@iwatamedea1 I probably need a stronger. I bought a starter pack of paint and it came with cleaner. The air brush is also a cheap starter model. I have some commercial thinners and cleaners I'll try, I was just using what came with the kit.

Glad that it was helpful. Happy painting!

Thank you for watching and for taking the time to comment. Our QuickTech videos are intentionally visually-focused rather than language-focused. This makes the series accessible to Iwata users worldwide and keeps distractions to a minimum. We hope you found the video helpful!

A new brush is lubricated at the factory and comes read-to-use. After use and cleaning, we recommend lubing the needle because the cleaning solvents will have removed the lubrication. Just a tiny dab will do, don't apply too much.

Thank you for the feedback! Almost everything can be fixed

If you need technical assistance, we can help. See common issues or ask a technical question on our website - www.iwata-airbrush.com/blog/troubleshooting/

To learn more about Createx Colors please visit them on their site at createxcolors.com

Airbrush nozzles are made from soft metals so that they form a tight seal that creates the performance needed. Nozzles are considered a wear and tear part like the tires on a car. As a normal expectation, they may need to be replaced from time to time and most people keep a few on hand

lol true!